Application: Shower, washroom, interior & exterior spaces, machinery spaces, etc.
Approvals: CSA C22.2 No. 250.0-00
Protection Class:  IP67
Housing:  Aluzinc sheet steel, deep drawn seamless
Finish: Epoxy powder coat, white RAL 9016
Diffuser: 5mm clear acrylic diffuser attached by two screws. Sealed by neoprene gasket.
Electrical: Flexible wiring, heat resistant to 105°C
Cable Entry:  one PG16 cable gland in one end and one blind PG16 plug in the other end.
Lamp Base: G5
Light Sources (not included): Fluorescent Tube, T5 8W
Supply voltage: 120v 60hz h.p.f.c.
Mounting:  Direct to bulkhead or deckhead
Part Number: MT-GSV-xxxx

Click on any image to see a larger version of the picture and then use the "Back" button in your browser to return to this page

Watertight, Multipurpose, Fluorescent
Surface Mount

Application: Decks, machinery spaces, stores, holds, etc
Approvals: UL 1598 & 1598A, and CSA C22.2 No. 250.0-00
Protection Class:  IP54 or IP67
Housing:  Aluzinc sheet steel, or Stainless Steel, deep drawn, seamless.
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Clear polycarbonate
Electrical: Flexible wiring, heat resistant to 105°C, through wiring up to 15 amps
Cable Entry:  One PG16 cable gland and one PG16 blind plug in each end. Other configurations available on request
Lamp Base: G13
Light Sources (not included): Fluorescent Tubes, T12,  20 or 40w  used with magnetic ballasts; T8, 17 or 36w used with electronic ballasts,
Optional Battery Backup: 500-600 lumens for 90 minutes at 20°C. Other configurations on request
Charge Time after full discharge: 24 hours
Mounting: 2 brackets for direct mounting to bulkhead or deckhead. Custom mounting brackets are also available.
Supply voltage: 120v 60hz h.p.f.c. with magnetic ballast, 120-277v 50-60hz h.p.f.c. with Electronic Ballasts
Versions available:  dual fluorescent tube 2ft or 4ft fixtures, with or without battery backup, with magnetic or electronic ballasts
Remarks: Low temperature ballasts are available on request.
Part Number: MT-GKI-xxxx

   Click on any image to see a larger version of the picture and then use the "Back" button in your browser to return to this page

Watertight, Multipurpose, Fluorescent
Surface Mount

Application: Decks, machinery spaces, stores, holds, etc
Approvals: UL 1598 & 1598A, and CSA C22.2 No. 250.0-00
Protection Class:  IP54 or IP67
Housing:  Aluzinc sheet steel, or Stainless Steel, deep drawn, seamless.
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Clear polycarbonate
Electrical: Flexible wiring, heat resistant to 105°C, through wiring up to 15 amps
Cable Entry:  One PG16 cable gland and one PG16 blind plug in each end. Other configurations available on request
Lamp Base: G13
Light Sources (not included): Fluorescent Tubes, T12,  20 or 40w  used with magnetic ballasts; T8, 17 or 36w used with electronic ballasts,
Optional Battery Backup: 500-600 lumens for 90 minutes at 20°C. Other configurations on request
Charge Time after full discharge: 24 hours
Mounting: 2 brackets for direct mounting to bulkhead or deckhead. Custom mounting brackets are also available.
Supply voltage: 120v 60hz h.p.f.c. with magnetic ballast, 120-277v 50-60hz h.p.f.c. with Electronic Ballasts
Versions available:  dual fluorescent tube 2ft or 4ft fixtures, with or without battery backup, with magnetic or electronic ballasts
Remarks: Low temperature ballasts are available on request.
Part Number: MT-GLIN-xxxx

Click on any image to see a larger version of the picture and then use the "Back" button in your browser to return to this page

Watertight, Multipurpose, Fluorescent
Surface Mount

Application: Decks, machinery spaces, stores, holds, etc
Approvals: UL 1598 & 1598A,
Protection Class:  IP54 or IP67
Housing:  Aluzinc sheet steel, or Stainless Steel, deep drawn, seamless.
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Clear polycarbonate
Electrical: Flexible wiring, heat resistant to 105°C, through wiring up to 15 amps
Cable Entry:  One PG16 cable gland and one PG16 blind plug in each end. Other configurations available on request
Lamp Base: G13
Light Sources (not included): Fluorescent Tubes, T12,  20 or 40w  used with magnetic ballasts; T8, 17 or 36w used with electronic ballasts,
Optional Battery Backup: 500-600 lumens for 90 minutes at 20°C. Other configurations on request
Charge Time after full discharge: 24 hours
Mounting: 2 brackets for direct mounting to bulkhead or deckhead. Custom mounting brackets are also available.
Supply voltage: 120v 60hz h.p.f.c. with magnetic ballast, 120-277v 50-60hz h.p.f.c. with Electronic Ballasts
Versions available:  dual fluorescent tube 2ft or 4ft fixtures, with or without battery backup, with magnetic or electronic ballasts
Remarks: Low temperature ballasts are available on request.
Part Number: Type-1444 MT-080100xxxx

Click on any image to see a larger version of the picture and then use the "Back" button in your browser to return to this page

Wet Location Light Fixture
suitable for marine, industrial or minning

Application: Severe industrial applications including wet and abrasive environments. Designed to prevent dust from collecting on lens.
Approvals: CSA C22.2 No. 250.0-00
Protection Class:  NEMA 13
Housing:  Sheet aluminum
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Safety glass
Reflector: Highly polished Aluminum, anodized. Available in wide beam (50°) or Narrow  beam (26°)
Electrical: Flexible wiring, heat resistant to 105°C; through wiring to 15 Amps
Cable Entry:  One 3/4" hole in one end and one 3/4" blind plug in the other end.
Lamp Base: G13, push on spring loaded lampholders
Light Sources (not included): Fluorescent Tubes 32w T8 with electronic ballasts
Mounting: Integral mounting brackets for double chain hanging.
Supply voltage: 120-277v 50-60hz, h.p.f.c.
Versions available:  2 32w fluorescent lamps
Part Numbers: MT-GIOC-1007 or 1008

Click on any image to see a larger version of the picture and then use the "Back" button in your browser to return to this page

Wet Location Light Fixture
suitable for marine, industrial or mining

Application: Designed as alternative for the traditional brass globe light with or without a guard. It is also available with many different coloured globes for use as a signal light, Ideal for salt water locations
Approvals: UL 1598 & 1598A
Protection:  Watertight, superior corrosion resistance
Housing:  Special black rigid plastic
Globe: Impact resistant clear rigid plastic, available in clear, green, red, blue and yellow
Cable Entry:  Four PG16 threaded openings with knockouts. One PG16 cable gland supplied. Please order additional cable glands separately.
Lamp Base: G23, medium screw base socket
Light Sources (not included): Incandescent 100W max or compact fluorescent 9w G23 base
Mounting: 2 integral brackets for direct mounting to deckhead. Optional wall mounting bracket also available, Please order separately.
Supply voltage: 277v max.
Versions available:  9w fluorescent or Incandescent 100w max for clear globe and  75w max for coloured globes.
Part Numbers: MT-080200xxxx  MariTeam type 1995

Click on any image to see a larger version of the picture and then use the "Back" button in your browser to return to this page