| Fluorescent, Surface Mount
Application: Hazardous areas: decks, process areas, machinery spaces, etc. Class 1 Division 2 and Class 1 Zone 2
Approvals: Class 1 Div. 2 Groups A, B, C, D, UL844, UL924, and CSA C22.2 No. 137-M1981
Protection Class: IP67
Housing: Aluzinc sheet steel, or stainless steel, deep drawn seamless
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Clear polycarbonate
Electrical: Flexible wiring, heat resistant to
105°C, through wiring up to 15 amps
Cable Entry: one 1/2" conduit hub and one blind plug at each end
Lamp Base: G13
Light Sources
(not included):
Fluorescent Tubes, with magnetic ballast, T12 20 or 40w
tubes, with electronic ballast, T8 17 or 36w tubes
Optional Battery Backup: 500-600 lumens for 90 minutes at 20°C, other configurations on request
Charge Time after full discharge: 24 hours
Mounting: 2 brackets for direct mounting to bulkhead or deckhead. Custom mounting brackets are also available
Remarks: low temperature ballasts available on request
Supply voltage: 120v 60hz h.p.f.c. with magnetic ballast, 120-277v 50-60hz h.p.f.c. with Electronic Ballasts
Versions available: dual fluorescent tube 2ft or 4ft fixtures, with or without battery backup, with magnetic or electronic ballasts
Part Number: MT-GXPN-xxxx |
Click on any image to see a larger version of the
picture
and then use the "Back" button in your browser to return to this page
 |
| Fluorescent, Surface Mount
Application: Hazardous areas: decks, process areas, machinery spaces, etc. Class 1 Division 2 and Class 1 Zone 2
Approvals: Class 1 Div. 2 Groups A, B, C, D, UL844, UL924, and CSA C22.2 No. 137-M1981
Protection Class: IP67
Housing: Aluzinc sheet steel, or stainless steel, deep drawn seamless
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Clear polycarbonate
Electrical: Flexible wiring, heat resistant to
105°C, through wiring up to 15 amps
Cable Entry: one 3/4" conduit hub at each end
Lamp Base:
Recessed Double Contact
Light Sources
(not included):
Fluorescent Tubes, 60W T12 high output
electronic ballast
Optional Battery Backup: 500-600 lumens for 90 minutes at 20°C, other configurations on request
Charge Time after full discharge: 24 hours
Mounting: 2 brackets for direct mounting to bulkhead or deckhead.
Supply voltage: 120v 60hz h.p.f.c. with magnetic ballast, 120-277v 50-60hz h.p.f.c. with Electronic Ballasts
Versions available: dual fluorescent tube 60w fixtures, with or without battery backup, with magnetic or electronic ballasts
Part Number: MT-1079-xxxx |
Click on any image to see a larger version of the
picture
and then use the "Back" button in your browser to return to this page
|
|
Fluorescent, Recessed Mount
Application: Hazardous areas: process areas, machinery control spaces, etc. Class 1 Division 2 and Class 1 Zone 2
Approvals: Class 1 Div. 2 Groups A, B, C, D, UL844, UL924, and CSA C22.2 No. 137-M1981
Protection Class: IP54
Housing: Aluzinc sheet steel
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Clear polycarbonate or clear prismatic
Electrical: Flexible wiring, heat resistant to
105°C, through wiring up to 15 amps
Cable Entry: one 1/2" conduit hub and one blind plug at each end
Lamp Base: G13
Light Sources
(not included):
Fluorescent Tubes, with magnetic ballast, T12 20 or 40w
tubes, with electronic ballast, T8 17 or 36w tubes
Optional Battery Backup: 500-600 lumens for 90 minutes at 20°C, other configurations on request
Charge Time after full discharge: 24 hours
Mounting: Designed for recessed parallel mounting in a linear interlocking ceiling system (Dampa, Dana Acoustic, BIP, etc.)
Supply voltage: 120v 60hz h.p.f.c. with magnetic ballast, 120-277v 50-60hz h.p.f.c. with Electronic Ballasts
Versions available: dual fluorescent tube 2ft or 4ft fixtures, with or without battery backup, with magnetic or electronic ballasts
Part Number: MT-GXPR-xxxx |
Click on any image to see a larger version of the
picture
and then use the "Back" button in your browser to return to this page
 |
|
Fluorescent, Surface Mount
Application: Hazardous areas: decks, process areas, machinery spaces, etc. Class 1 Division 2 and Class 1 Zone 2zone 1 and 2
Approvals: CSA approved Class 1 Div. 1 Groups C & D, flame proof for extreme safety
Protection Class: IP67
Housing: Corrosion resistant light weight aluminum alloy
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Clear polycarbonate
Electrical: Flexible wiring, heat resistant to 105°C, all electrical components installed on a fully removable gear tray
Cable Entry: Internal junction box with
two 3/4" NPT entries.
Lamp Base: G13
Light Sources (not included):
Fluorescent Tubes, T8 17w or 36w tubes
Optional Battery Backup: 500-600 lumens for 90 minutes at 20°C, other configurations on request
Charge Time after full discharge: 24 hours
Mounting: Stainless steel hinged swing brackets enable the fixture to be mounted end to end.
Features: removable gear tray allows for quick and easy maintenance. Fixture
can be converted to an "emergency fixture by simply replacing normal gear tray with an "emergency" gear tray.
Remarks: low temperature ballasts available on request
Supply voltage: 120v 60hz h.p.f.c. with magnetic ballast, 120-277v 50-60hz h.p.f.c. with Electronic Ballasts
Versions available: dual fluorescent tube 2ft or 4ft fixtures, with or without battery backup, with magnetic or electronic ballasts
Part Numbers: MT-183300xxxx |
Click on any image to see a larger version of the
picture
and then use the "Back" button in your browser to return to this page
 |
|
Fluorescent, Surface Mount
Application: Hazardous areas: decks, process areas, machinery spaces, etc. Class 1, Zone
1 & 2 areas
Approvals: CSA approved Class 1 Zone 1,
Ex edm IIC - T5 (T4 with battery backup)
Protection Class: IP67
Housing: Aluzinc sheet steel, or stainless steel, deep drawn seamless
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Clear polycarbonate
Electrical: Flexible wiring, heat resistant to
105°C, through wiring up to 15 amps
Cable Entry: M20, M25 or
PG16. One or two entries per end. Please specify when ordering.
Lamp Base: G13
Light Sources
(not included):
Fluorescent Tubes, with electronic ballast,
17/32W T8
Optional Battery Backup: 1.5 hour or 3.0 hour battery backup.
Suitable for use in an ambient temperature up to 45°C
Mounting: 2 brackets for direct mounting to bulkhead or deckhead. Custom mounting brackets are also available
Part Number: MT-MAX-xxxx |
Click on any image to see a larger version of the
picture
and then use the "Back" button in your browser to return to this page
 |
|
Flood HPS or MH
with Internal Ballast and Igniter
Application: For supreme safety, Hazardous areas, Class 1 Zone 1, interior or exterior.
Approvals: UL approved Class 1 Zone 1, Ex de IIB - T3
Protection Class: IP66
Housing: Corrosion resistant light weight aluminum alloy
Finish: Epoxy powder coat, white RAL 9016
Diffuser: 19mm thick heat tempered thermal and shock resistant borosilicate glass
Reflector: Aluminum
Ballast: Internal, h.p.f.c.
Cable Entry: Internal
junction box, AEx e with screw terminals and two 3/4" NPT entries.
Lamp Base: E39, Mogul screw base
Light Sources
(not
included): 150 ro 250w HPS or MH lamps
Mounting: Stainless steel brackets for deck or bulkhead mounting
Features: Threaded lamp access cover, allows for easy relamping by simply removing cover, no screws or
bolts to be removed. All hardware made of of corossion resistant stainless steel. Simplified maintenance, only four screws to be removed to change ballast components.
Supply voltage: 120v/240vac h.p.f.c.
Versions available: 3, 150w HPS, 250w HPS, and 250w MH
Part Numbers: MT-1796xxxxxx |
Click on any image to see a larger version of the
picture
and then use the "Back" button in your browser to return to this page
 |
|
Flood HPS with Internal Ballast
Application:
Fully self contained high pressure sodium floodlight for hazardous areas Class 1 Div. 2 and Zone 2.
Approvals: Class 1, Div. 2, Groups A, B, C, D, UL844
Protection Class: IP67
Housing: Stainless steel deep drawn seamless
Finish: Epoxy powder coat, white RAL 9016
Diffuser: Easy to change safety glass, no tools required for relamping.
Reflector: Highly polished Aluminum, anodized. Available in wide beam (50°) or Narrow
beam (26°)
Electrical: Flexible wiring, heat resistant
Cable Entry: External junction box with one 3/4" conduit hub. .
Lamp Base: E39, Mogul screw
base
Light Sources (not included):
250 or 400w HPS
lamps
Mounting: Two adjustable Stainless steel brackets with two mounting holes each, OD 14mm
Remarks: Internal Ballast and igniter included
Supply voltage: 120/208/240/277vac h.p.f.c.
Versions available: wide or narrow beam, 250 or 400w
Part Numbers: MT-1069-028, 029, 030, 031 |
Click on any image to see a larger version of the
picture
and then use the "Back" button in your browser to return to this page
 |
